Chkdsk Command

Chkdsk Command Examples, Options, Switches, and More

Screenshot of the Chkdsk command in Windows 10 Command Prompt
Chkdsk Command (Windows 10).

Short for "check disk," the chkdsk command is a Command Prompt command used to check a specified disk and repair or recover data on the drive if necessary.

Chkdsk also marks any damaged or malfunctioning sectors on the hard drive or disk as "bad" and recovers any information still intact.

Chkdsk Command Availability

The chkdsk command is available from the Command Prompt in Windows 10, Windows 8, Windows 7, Windows Vista, and Windows XP operating systems.

The chkdsk command is also available via Command Prompt in Advanced Startup Options and System Recovery Options. It also works from within the Recovery Console in Windows 2000 and Windows XP. Chkdsk is a DOS Command too, available in most versions of MS-DOS.

Note: The availability of certain chkdsk command switches and other chkdsk command syntax might differ from operating system to operating system.

Chkdsk Command Syntax

chkdsk [volume:] [/F] [/V] [/R] [/X] [/I] [/C] [/L:size] [/perf] [/scan] [/?]

Tip: See How to Read Command Syntax if you're not sure how to interpret the chkdsk command syntax above or described in the table below.

volume:This is the drive letter of the partition for which you want to check for errors.
/FThis chkdsk command option will fix any errors found on the disk.
/VUse this chkdsk option on a FAT or FAT32 volume to show the full path and name of every file on the disk. If used on an NTFS volume, it will show cleanup messages (if there are any).
/RThis option tells chkdsk to locate bad sectors and recover any readable information from them. This option implies /F when /scan is not specified.
/XThis command option implies /F and will force a dismount of the volume if necessary.
/IThis option will perform a less vigorous chkdsk command by instructing the command to run faster by skipping over certain regular checks.
/CSame as /I but skips over cycles within the folder structure to reduce the amount of time that the chkdsk command runs.
/L:sizeUse this chkdsk command option to change the size (in KB) of the log file. The default log file size for chkdsk is 65536 KB; you can check the current log file size by executing /L without the "size" option.
/perfThis option allows chkdsk to run faster by using more system resources. It has to be used with /scan.
/scanThis chkdsk option runs an online scan on an NTFS volume but does not try to repair it. Here, "online" means that the volume does not need to be dismounted, but can instead remain online/active. This is true for both internal and external hard drives; you can continue using them throughout the course of the scan.
/spotfixThis chkdsk option dismounts the volume only briefly in order to fix issues that were sent to the log file.
/?Use the help switch with the chkdsk command to show detailed help about the commands listed above and other options you can use with chkdsk.

Note: Other less commonly used chkdsk command switches exist too, like /B to re-evaluate bad clusters on the volume, /forceofflinefix which runs an online scan (a scan while the volume is active) but then forces the repair to run offline (once the volume has been dismounted), /offlinescanandfix which runs an offline chkdsk scan and then fixes any problems that were found, and others that you can read more about through the /? switch.

Note: The /offlinescanandfix option is the same as /F except that it's only allowed on NTFS volumes.

If you're using the chkdsk command from the Recovery Console in older versions of Windows, use /p in place of /F above to instruct chkdsk to perform an extensive check of the drive and correct any errors.

Chkdsk Command Examples

chkdsk

In the above example, since no drive or additional options were entered, chkdsk simply runs in read-only mode.

Note: If problems were found when running this simple chkdsk command, you'll want to make sure to use the example from below to correct any issues.

chkdsk c: /r

In this example, the chkdsk command is used to perform an extensive check of the C: drive to correct any errors and to locate any recovery information from bad sectors. This is best used when you're running chkdsk from outside of Windows, like from a recovery disc where you need to specify which drive to scan.

chkdsk c: /scan /forceofflinefix

This chkdsk command runs an online scan on the C: volume so that you don't have to dismount the volume to run the test, but instead of fixing any issues while the volume is active, the problems are sent to a queue that will be resolved in an offline repair.

chkdsk c: /r /scan /perf

In this example, chkdsk will fix problems on the C: drive while you're using it, and will use as much system resources as allowed so that it will run as quickly as possible.

Chkdsk Related Commands

Chkdsk is often used with many other Recovery Console commands.

The chkdsk command is similar to the scandisk command used to check a hard drive or floppy disk for errors in Windows 98 and MS-DOS.

Was this page helpful?